Đếm từ 0 - 99 with XC8 PIC18F452

Chào các bạn trong bài đăng này mình sẽ hướng dẫn các bạn lập trình cho PIC18F452.

Ảnh mô phỏng protues.

Đây là code chương trình.

#include <stdio.h>
#include <stdlib.h>
#include <pic18f452.h>
#define _XTAL_FREQ 4000000
#include "xc.h"
// CONFIG1H
#pragma config OSC = XT         // Oscillator Selection bits (XT oscillator)
#pragma config OSCS = OFF       // Oscillator System Clock Switch Enable bit (Oscillator system clock switch option is disabled (main oscillator is source))

// CONFIG2L
#pragma config PWRT = OFF       // Power-up Timer Enable bit (PWRT disabled)
#pragma config BOR = OFF        // Brown-out Reset Enable bit (Brown-out Reset disabled)
#pragma config BORV = 20        // Brown-out Reset Voltage bits (VBOR set to 2.0V)

// CONFIG2H
#pragma config WDT = OFF        // Watchdog Timer Enable bit (WDT disabled (control is placed on the SWDTEN bit))
#pragma config WDTPS = 128      // Watchdog Timer Postscale Select bits (1:128)

// CONFIG3H
#pragma config CCP2MUX = OFF    // CCP2 Mux bit (CCP2 input/output is multiplexed with RB3)

// CONFIG4L
#pragma config STVR = OFF       // Stack Full/Underflow Reset Enable bit (Stack Full/Underflow will not cause RESET)
#pragma config LVP = OFF        // Low Voltage ICSP Enable bit (Low Voltage ICSP disabled)

// CONFIG5L
#pragma config CP0 = OFF        // Code Protection bit (Block 0 (000200-001FFFh) not code protected)
#pragma config CP1 = OFF        // Code Protection bit (Block 1 (002000-003FFFh) not code protected)
#pragma config CP2 = OFF        // Code Protection bit (Block 2 (004000-005FFFh) not code protected)
#pragma config CP3 = OFF        // Code Protection bit (Block 3 (006000-007FFFh) not code protected)

// CONFIG5H
#pragma config CPB = OFF        // Boot Block Code Protection bit (Boot Block (000000-0001FFh) not code protected)
#pragma config CPD = OFF        // Data EEPROM Code Protection bit (Data EEPROM not code protected)

// CONFIG6L
#pragma config WRT0 = OFF       // Write Protection bit (Block 0 (000200-001FFFh) not write protected)
#pragma config WRT1 = OFF       // Write Protection bit (Block 1 (002000-003FFFh) not write protected)
#pragma config WRT2 = OFF       // Write Protection bit (Block 2 (004000-005FFFh) not write protected)
#pragma config WRT3 = OFF       // Write Protection bit (Block 3 (006000-007FFFh) not write protected)

// CONFIG6H
#pragma config WRTC = OFF       // Configuration Register Write Protection bit (Configuration registers (300000-3000FFh) not write protected)
#pragma config WRTB = OFF       // Boot Block Write Protection bit (Boot Block (000000-0001FFh) not write protected)
#pragma config WRTD = OFF       // Data EEPROM Write Protection bit (Data EEPROM not write protected)

// CONFIG7L
#pragma config EBTR0 = OFF      // Table Read Protection bit (Block 0 (000200-001FFFh) not protected from Table Reads executed in other blocks)
#pragma config EBTR1 = OFF      // Table Read Protection bit (Block 1 (002000-003FFFh) not protected from Table Reads executed in other blocks)
#pragma config EBTR2 = OFF      // Table Read Protection bit (Block 2 (004000-005FFFh) not protected from Table Reads executed in other blocks)
#pragma config EBTR3 = OFF      // Table Read Protection bit (Block 3 (006000-007FFFh) not protected from Table Reads executed in other blocks)

// CONFIG7H
#pragma config EBTRB = OFF      // Boot Block Table Read Protection bit (Boot Block (000000-0001FFh) not protected from Table Reads executed in other blocks)

void GPIO_init(void);
void display(unsigned int digit);
unsigned int digit = 0;
const unsigned char seg[]={0x3F,0x06,0x5B,0x4F,0x66,0x6D,0x7D,0x07,0x7F,0x6F};
void main(void)
{
    GPIO_init();
    while(1)
    {    
      __delay_ms(10);
      display(digit);
      __delay_ms(100);
      digit++;
      if(digit==99)
      {
          digit=0;
      }
    }
}
void GPIO_init(void)
{
    TRISC = 0X00;
    LATC = 0X00;
    TRISD = 0X00;
    LATD = 0X00;
    TRISB0 = 0;
    TRISB1 = 0;
}
void display(unsigned int digit)
{
    unsigned int ten,one;
    one = (digit)%10;
    ten = (digit)/10;

    PORTBbits.RB0 = 0;
    LATD = seg[one];
    __delay_ms(10);
    PORTBbits.RB0 = 1;

    PORTBbits.RB1 = 0;
    LATC = seg[ten];
    __delay_ms(10);
    PORTBbits.RB1 = 1;   
}

Link download project.
http://www.mediafire.com/download/pf5i8tydsky7afh/0_99.rar

Share this

Author : Unknown

Related Posts